The author is making a few good pointers on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround as a whole in this article directly below.
Installing a bathtub isn't precisely rocket science, but it does need strong plumbing, carpentry, and often, tiling skills. Changing an old tub with a new one is additionally a reasonably challenging project. If the old bathtub is conveniently accessible, the job can move immediately; if you need to open up a wall surface to get rid of the old bathtub and also position the new bath tub, the job is a lot harder. In either case, the task is within a residence handyman's skills, although you will need a helper to move out the old tub and set in the new one. Ensure you have qualified yourself for the work and also fit trying it. As opposed to working with a service provider to take control of a halfway-completed task, it is far better to take into consideration utilizing one before you begin. Chances are you may require a specialist plumber to make tube connections.
This article will help you install a brand-new bath tub in your washroom if you have already purchased a new bathtub and also don't need to change the setup of your previous water pipelines.
Your tools and material list need to make up the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly problematic due to the limited gain access to that is often the situation.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipes have been gotten rid of, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin guaranteeing that the washing machines remain in place between the faucet and the sink. Safeguard the tap in position with the manufacturer offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular faucet connectors. The previous type must be connected to the tap finishes first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bath tub
Using the two wood boards under its feet, place the tub in the called for position. The wooden boards are handy in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following objective is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the bathtub until the spirit level checks out degree.
To mount faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression join; then do the exact same for the other tap.
Turn on the water system as well as examine all joints and also brand-new pipework for leakages and also tighten them if essential. Fill the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the maker's user's manual. Tiling as well as securing around the tub ought to wait until the bathtub has been made use of at the very least when as this will certainly resolve it into its final setting.
Preparing for the Installation
Firstly, the supporting frame provided with the bathroom must be fitted (if required) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to ensure that if the tap features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets device to avoid stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of both faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to crack an inflexible seal, causing the water to pass through the wall in between the bath and the tiling, bring about complications with moisture and also possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and fittings. They are marketed in tubes and cartridges, as well as are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bathtub with water prior to securing, to permit the movement experienced when the tub remains in usage. The sealer can break relatively very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly readily available on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or waterproof sticky and also grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
We hope you liked our piece about How to Install a Bathtub Yourself. Thanks a lot for finding the time to browse our short article. Enjoyed our piece? Please share it. Help someone else locate it. I praise you for your time. Please visit our site back soon.
Request An Appointment